Plastering walls with plasterboard in a wooden house in 5 steps is simple and clear

A warm, oxygen-rich wooden house provides an environmentally friendly microclimate and an aesthetically pleasing appearance. Walls made of wood, even after final shrinkage, continue to “breathe”, changing in size. This property of natural material is associated with some difficulties in interior decoration. The best option for a wooden house is to cover the walls with plasterboard. Light weight, simple installation and availability of pressed sheets allow you to level the surfaces of walls and ceilings without the involvement of specialists.

Features of installing drywall in a wooden house

Wood is a natural material that not only has positive properties, but also some disadvantages. To avoid negative consequences during the construction and operation of a wooden house, it is important to take into account its features. The question of how to sheathe the inside of a wooden house with plasterboard correctly and complete the interior finishing can be solved by following the rules for its installation:

1. Before installing drywall sheets, wooden walls are treated with antiseptic agents that will protect against the appearance of rot, mildew and mold.
2. The wood is coated with fire retardants to protect the log or timber house from fire. These can be two-in-one antiseptic-fire retardant products.
3. Plasterboard finishing is carried out after partial shrinkage of a wooden house - a year after construction.
4. In case of additional insulation from the inside, a vapor barrier film is laid under the plasterboard sheets. The vapor barrier film prevents the formation of condensation in the insulation.
5. Caulking cracks in the crown of the house and sealing cracks in logs and beams will help prevent the appearance of moisture on drywall.
6. After the building shrinks, the building material is mounted on a frame that is not rigidly connected to the ceiling and floor of the house.

A deformation gap of 30-50 mm is left between the plasterboard and the floor or ceiling. To do this, pads made of any building materials are placed on top and bottom of the plasterboard sheets. Then they are removed. After finishing, the gaps are closed with decorative skirting boards. The frame must also be independent of the supporting foundation of the house so that the drywall does not deform during operation.

It is very important that the frame is secured to the “slippers” and is floating

How to build a frame for plasterboard sheathing

In the case of a wooden house, you can go in different ways:

1) If the cladding is carried out in a house that was built several years ago and has settled sufficiently in height, you can mount a fixed frame of slats. To work you will need:

• 75×25 mm slats for guides for gypsum board joints;
• 50×25 slats for sheet guides;
• Self-tapping screws;
• Metal corners for fastening slats;
• Screwdriver;
• Ruler, pencil and stationery knife for marking and cutting gypsum boards.

Horizontal slats are attached along the lower edge and under the ceiling. In this case, the lower one lies on the finished floor, the upper one does not reach the ceiling 1-2 cm. The placement of vertical guides begins from the corner. The distance between the main slats along the central axes should be equal to the width of the sheet. Internal slats are set in increments of 400 mm, i.e. 2 auxiliary slats for 1 sheet with a width of 1205 mm.

The slats are fastened to the wall using self-tapping screws or nails. The installation of each guide must be accompanied by checking verticality with a level or plumb line. The main and auxiliary elements can be attached to the horizontal floor and ceiling rails either with metal corners or with self-tapping screws, directing them to the support point at an angle of 45°.

It is important to check not only the strict verticality of the guides, but also the evenness of the plane to which the drywall will be attached. For control, it is optimal to use a long, flat rod or a construction rule.

2) The movable frame is suitable for installation in a newly built house, in which the rigid frame given above is deformed when the structure shrinks. You will need the same set of tools, only as a moving element you need to purchase “crab” attachments and PAZ 2 strips. The plank is attached to the wall motionlessly; a crab pre-installed on it with a rail can move along it within 6 cm when it shrinks. They tell you more about installation masters in the video. The work algorithm also applies to wooden frames.

3) Another interesting way to install a movable frame without complex devices. Fastening is carried out not to the wall, but to the ceiling. To do this, nylon plugs are inserted into the places marked on it. They will protect metal and wood from negative effects on each other. Holes are drilled in the ceiling beam at the attachment point, into which a long bolt and washer are threaded. It turns out that the upper part of the frame is not firmly fixed, but suspended. Thus, we leave the structure the opportunity to maintain its integrity and not change its position when the main wall shrinks and the ceiling lowers.

The guide rails are screwed into the ceiling and floor beams and to the walls along their length.

Advantages and disadvantages

• low cost. To cover the walls of a house with plasterboard, you will need a much smaller amount than when finishing with clapboard;
• easy and quick installation. Drywall sheets are large in size, so they can sheathe large surface areas of walls and ceilings in a fairly short time;
• plastic. The material bends easily. It can be given any shape from rectangular cascades to semicircular arches;
• has good thermal insulation properties, which allows you to save on energy costs and heating;
• has light weight. You can make the interior lining with plasterboard alone, with your own hands, without anyone’s help;
• During installation, free space is created under the drywall in which utility lines can be hidden;
• environmentally friendly material. It does not contain toxic or synthetic additives and is safe for human health;
• The constituent element of gypsum board is gypsum. It is fireproof. Only the cardboard part of the material can ignite, but only from the side of the fire. There are also fire-resistant plasterboard sheets that are not afraid of fire;

• fragility. Drywall can break off during transportation, operation, or installation. Therefore, it must be handled with care. To hang a heavy item on a plasterboard box, you need to use special fasteners. They will help avoid damage to the material;
• cannot withstand temperature changes. It is mounted at a temperature not lower than -10 degrees;
• It occupies a significant area, so it is not used in small rooms.

Preparatory work

Before you begin installing drywall on the ceiling or walls of a wooden house, you need to perform certain preliminary work, which includes:

• preparing the base;
• determining the need for materials;
• preparing the necessary tools and equipment.

Preparing the base of wooden surfaces

• trim the most protruding places;
• caulk and caulk cracks between logs, beams or boards;
• treat wooden surfaces with antiseptics to protect against rot and mold;
• Fire retardants are applied - compounds that do not allow wood to sustain combustion and increase the flash point.

Material calculation

To determine the amount of material required, it is determined what the frame will be made of, wooden slats or metal profiles.

Over time, wooden slats can also be subject to various deformations, which will be transmitted to the plasterboard sheets, bending them and causing cracks in the seams. Therefore, to make the frame, it is better to use metal elements with a channel-shaped profile, specially designed for drywall.

When sheathing timber, logs or boards, it is not recommended to install plasterboard sheets without a frame, nailing them to wooden planes. In this case, most of the defects will appear on the panels; they will become curved, wavy, with seams of uneven thickness. Leveling will require applying a thick layer of putty, which will begin to fall off over time due to seasonal deformations of the wooden house.

Next, a plan of the walls and ceiling is drawn in the form of a sweep. Having calculated the working surface area, subtracting all openings - door, window openings, radiator installation locations, etc., and multiplying it by 20...25% (safety factor), we divide the result by the area of ​​one sheet with standard dimensions 2500 x 1200 mm, we obtain the required quantity GKL in pieces.

Tool

- electric drill; - screwdriver; - knife for cutting sheets; - hacksaw for wood; - construction corner; — staff-rule 1.2…1.5 m; — bubble level (for leveling when installing the frame); - plumb line (for wall cladding); - water level (for ceiling cladding); - hammer; - stepladder, scaffolding.

Types of drywall

According to the intended purpose, plasterboard can be:

• arched. This material is thin 6.5 mm thick;
• ceiling It is intended for arranging suspended structures and finishing ceilings in dry rooms with humidity up to 70%. Its thickness is 9.5 mm;
• wall It is used for cladding walls and arranging interior partitions. Its thickness is 12.5mm.

According to technological features, plasterboard is divided into:

• standard or regular plasterboard;
• moisture-resistant gypsum board;
• fire-resistant gypsum plasterboard;
• moisture-resistant and fire-resistant;
• acoustic. It is used in rooms where increased sound insulation is required.

The material varies according to the type of edge. The edge is:

• straight. Gaps between straight-edged sheets are not sealed. Designated PC;
• Refined edge of the UK. The joints between sheets with such an edge should be puttied, reinforced with sickle mesh;
• the semicircular edge is sealed with putty, but not reinforced (HRK);
• rounded edge of the lock.

Appearance of different drywall

Sliding frame made of wooden blocks

It is better to make a wooden frame for drywall from dense wood, such as pine or oak. Regardless of the type of tree, the frame elements must be treated with antiseptic solutions to prevent the formation of mold and rot and fire retardants to prevent the wood from burning.

The algorithm for performing the work is as follows:

1. The outline of the future frame is drawn on the floor and a projection is made onto the ceiling;
2. Next, mark the places where you plan to install sliding guides for drywall. It should be remembered that from the corner to the near post it is necessary to maintain a distance of about 0.6 meters. The edges of the drywall must rest on the bars;
3. For additional strength, intermediate slats are installed between the main bars in increments of 0.2 meters;
4. Metal corners are used as fastenings for vertical frame elements, on one side of which there is a vertical oval groove. Direct fixation is performed with a screw and washer. The corners are attached at a distance of 0.2-0.3 meters from each other;
5. The outer bars are placed first, between which a fishing line or cord is pulled to install intermediate elements;
6. The fixation of the bars should not be strong so that the bolts can move along the mounting angle when the house shrinks;
7. After installing all the vertical supports, proceed to the installation of horizontal struts; their location can be arbitrary. However, experts recommend installing the jumper so that the corner of the plasterboard sheet rests simultaneously on the vertical and horizontal frame element.

GVL

GCR is a material consisting of a gypsum core and 2 sheets of cardboard. The elements are connected using glue. Cardboard is used as a reinforcing element. It also gives shape to the material.

GVL are gypsum fiber sheets. They consist of a mixture of gypsum and fluff pulp. Waste paper is mixed with water and sheets are made under a press, which are then dried. They are used to level surfaces and frame frames. GVL is a more durable material. Unlike drywall, it can be used to finish floors.

Finishing gypsum fiber board walls in a wooden house is more labor-intensive. Before screwing the screws into the gypsum fiber, you need to drill holes.

Otherwise, it is impossible to tighten the hardware due to the high density and strength of the sheets. Heavy objects can be hung on a wall covered with gypsum plasterboard: shelves, mirrors. This material is suitable for finishing a bathroom in a wooden house. GVL is not flexible, so it cannot be used for arranging shaped elements.

COVERING SIDING PANELS FOR EXTERNAL WALLS OF A HOUSE ON THE LAKE SHORE

If you want a warm feeling from your exterior, cladding the facade with clapboard will give you this! Look at these photos of houses covered with wooden clapboards and you will see this. Fortunately, modern protective materials allow you not to think for a long time about restoring the facade of a wooden house.

Don’t be afraid to apply new technologies to old, proven materials and you will get ultra-modern wooden house facades that will delight you every day!

The one-story wooden house is located on Orcas Island, one of the archipelagos of San Juan Island off the coast of Washington, USA. The house is equipped with retractable panels that protect it from very windy storms, the prevailing ocean currents that come ashore in winter. Located on the coast of an island, the house uses both retractable wood panels and the surrounding forest for winter protection. Lining is widely used on the facade and interior of the house as a finishing material. But look how ultra-modern the cladding looks!

On the south side of the house there is a rocky shore overlooking the Pacific Ocean. The architects, answering the question of how to cover the facade of the house, used natural colors of cedar cladding on the facade to harmoniously combine this wooden house with the surrounding landscape. The lining material for the exterior cladding of the house is local.

The surrounding forest helps protect the house from weather conditions, which are severe quite often.

Stone collected from the site was used to level the area for the house. The space occupied by the house was compensated by the green roof on it.

The site is on an island with pristine shorelines and marine life, so carefully engineered stormwater flows were designed to replicate pre-construction conditions.

Wooden wall panels are installed on tracks, which allows them to close tightly or open widely depending on weather conditions.

When the weather is good and the panels are open - behind them is a wall of large panoramic windows, which can also be closed or opened wide for easy access to the outdoors.

This double sliding panel system is used on both the front and rear façade of this modern timber home.

When both sets of slides are open, you can easily walk through the house from the front yard to the back deck without opening the door.

The home's wide open spaces are ideal for allowing ocean views to travel unimpeded throughout the home and yard.

When the glass panels are closed and the wall panels remain open, cold parties remain comfortable.

The home's outdoor deck also boasts a large size, allowing you to enjoy outdoor dining.

This stunning outdoor dining table was crafted from two planks of naturally weathered building material.

The roof overhang and deck siding is Western Red Cedar.

Around the back of the house, the alcove is also lined with red cedar clapboard, and the open deck is left uncovered to weather conditions.

The back deck slopes down to the portion of the landscaping that was leveled for the home's foundation.

Inside the home, wood floors, clapboard ceilings and walls act as a frame for impressive views.

Even the view from the front of the house is magnificent and constantly showcases the local animal life.

When the wall panels are closed, the view to both sides of the house is still not completely blocked, and natural daylight can illuminate the interior areas.

On cold days, when the house is closed, a wood fireplace is used for heating. The design with open square shelving on both sides is the main focus when covering the wall panels. Even the wooden paneling of the ceiling of this wonderful interior does not create the impression of a grandmother’s dacha. As a nod to the color of the ocean and sky, several parts of the interior feature rich blue hues.

The indoor dining table is made from a slab of Fir wood, but unlike the outdoor dining table, it has not been treated for outdoor use. The kitchen overlooks the side façade and deck. It has four small storage rooms on the side walls. The overhangs on the other side of the house are longer and contain a master bedroom overlooking the side garden and ocean, as well as a guest suite overlooking the side garden and a master bathroom overlooking the front yard. Unlike the social area, there is no clapboard paneling in the bedrooms, bathroom and toilets.

Which to choose

To choose the right material, it is important to know the operating conditions of the premises.

For rooms, standard plasterboard is usually used; for rooms with high humidity: kitchen, toilet, bathroom - moisture-resistant.

If possible, you can buy fire-resistant drywall for the entire house. In this case, for the interior decoration of the kitchen and bathroom, the material must also be moisture resistant. Therefore, moisture-resistant GKLVO plasterboard sheets are chosen.

You should pay attention to the quality of the material.

It is better to buy drywall from a well-known brand to be sure of its strength characteristics, for example Knauf.

When choosing, you should determine for what purposes it will be used: for walls, for finishing the ceiling or for creating curly elements. Based on the purpose of the material, you need to select sheets of a certain thickness.

Frameless method

It is not at all necessary to install the frame: you can attach the drywall directly to the wall surface using a special adhesive. The advantage of this method is that it increases the usable area of ​​the room.

Disadvantages of the frameless method:

1. Suitable only for smooth walls, otherwise it will be difficult to install the sheets.
2. There is no way to lay wires or hide communications.
3. It is unacceptable to use an adhesive composition - it is not among the environmentally friendly materials.
4. It is impossible to apply insulation.

If profiled laminated veneer lumber was used to build a house, all of the listed disadvantages will not be observed (except for additional insulation) - this is a rare case when the walls will be almost perfectly smooth, so you can attach drywall directly to their surface.

Common mistakes

The most common errors include:

• laying sheets of drywall with the front side facing the wall. They should be positioned with the front side inward. When the front sides of the sheets are combined, a recess is formed at the joints, which is convenient for treating them with putty;
• the formation of cross-shaped seams leads to a deterioration in the strength of the material. Plasterboard sheets must be installed with offset seams;
• the location of the screws is close to the edge. When temperature changes occur, the metal expands and breaks the plaster. The fasteners should be located at a distance of 10-15 cm from the edge and always not opposite each other on adjacent sheets, but offset;
• The screws are screwed in incorrectly. The cap should not stick out from the sheet, this will make it difficult to putty the seams. The level of the hardware can be checked with a spatula. If, when passing the spatula along the surface of the sheet, the head touches the canvas, then the self-tapping screw must be tightened;
• the absence of a compensation gap from the floor and ceiling can lead to the formation of cracks at the joints. The gap should be 30-50 mm.

What is needed for finishing

Finishing the inner surface of the walls of a house with plasterboard requires careful selection of materials. The master will need to purchase:

1. GKL slabs are moisture- and fire-resistant (GKLVO).
2. A sufficient number of screws for wood or metal (depending on the chosen frame).
3. Putty and composition for priming drywall.
4. Silicone and polyurethane foam.
5. Solutions for impregnating timber to provide protection against insects and rodents.
6. Insulation boards and soundproofing materials.

Tools and materials
For installation and assembly of the metal frame, additional fasteners will be needed so that the structure can withstand increased loads; sheets of drywall should be sewn in 2 layers with an offset. You also need to stock up on vapor barrier, which will prevent moisture from the house from penetrating under the assembled structure and being absorbed into the wood.

Choosing timber for sheathing

If you decide to assemble a frame for drywall made of wood, then you need to approach the choice of material very carefully. The list is as follows:

The wood must be very well dried. In most cases, you can only buy raw timber at the sawmill, which you will have to dry yourself

The ideal option is considered to be a maximum moisture content of the construction timber of 14%. Each lath and beam must be inspected for defects: uneven and knotty material will create problems during assembly or sheathing. It is important that the lumber is of the same cross-section. For guides and frame posts, you can use the same type of timber 50×50, 40×40, 50×40 mm and others

It is advisable not to use smaller widths, because sheets of plasterboard will be joined and secured with self-tapping screws on the racks.

After purchasing the material, all slats need to be inspected again and treated with protective impregnations or at least painted

This will protect the forest from moisture penetration. It is important to remember that the timber and slats must be stored in a horizontal position, otherwise, over time, vertical storage will result in curved racks

Wall design options

The construction market is replete with various offers, forcing the modern consumer to rack his brains over the choice of finishing material.
Some opt for the simplest and most affordable methods, which are suitable both for finishing an old country house and new houses, which will be discussed below.

Painting

To implement this finishing option, you can use various types of paints (see photo), among which the most common are water-based and acrylic materials.

The advantages of this finishing method:

• painting is a very simple procedure that does not require special skills and tools;
• the painted surface can be easily repainted in a different color if necessary;
• an endless selection of colors and shades;
• ease of cleaning and disinfection.

Now about the disadvantages:

• Before painting, the walls require careful preparation, since if there is a rough surface, the paint will lie in an uneven layer, which will lead to the formation of peeling over time;
• the painted surface needs systematic wet cleaning;

Drywall

Installing drywall will not only allow you to perfectly align the walls in the room, but also lay thermal insulation material between the sheets and the main wall, if necessary.

Advantages of using drywall:

• quick and easy installation;
• the ability to construct structures of any complexity;
• drywall makes it easy to disguise wiring and various communications;
• Possibility of finishing with various finishing coatings.

Flaws:

• the usable area of ​​the room decreases;
• low resistance to mechanical stress;
• the need for additional puttying of seams and joints after installation, as well as puttying of the material over the entire area;
• Drywall is susceptible to high humidity, which negatively affects the service life of the material.

Textile

This finishing method was often used in the old days, but now it has received a rebirth. Both natural textiles and artificial materials are used to cover walls.

The fabric is attached in various ways: pasted like regular wallpaper, stretched onto pre-constructed wooden frames, which are then installed on the wall, and fixed to the wooden wall with a stapler.

Advantages of the method:

• there is no need to level the walls (except for those cases when fabric is glued instead of wallpaper);
• resistance to various mechanical damage - textiles simply stretch under load without being subject to ruptures or cracks;
• the room acquires a special chic thanks to the texture of the material;
• fabrics for wall decoration are made in a wide range, so there are many options to choose from, as well as the possibility of combining the material with curtains and bed linen.

Flaws:

• the fabric absorbs a large amount of dust, so the material must be vacuumed regularly;
• textiles quickly lose their appearance, get dirty and rubbed easily.

A traditional option that provides the modern consumer with a wider range of options than in the old days.

Today you can purchase not only paper wallpaper, but also vinyl, duplex, non-woven, textile and other types of materials.

Advantages of wallpapering:

• walls require less thorough preparation, unlike painting, which requires repairing even the smallest cracks and irregularities;
• large selection of different types of material;
• the ability to independently carry out finishing work with minimal skills.

Flaws:

• the need to replace wallpaper (except liquid wallpaper) after 5-7 years, as they quickly lose their appearance;
• susceptibility to mechanical damage;
• difficulties in removing dirt, even when it comes to washable wallpaper.

Wall panels

Wall panels are products intended for decorative finishing of walls. They can be made from various materials (chipboard, fibreboard, PVC, wood) and in different shapes - in the form of slabs, sheets and slats.

They are mounted like drywall on a frame, which in this case can be either steel or wood.

Advantages of panels:

• relatively simple installation;
• the possibility of equipping the wall with sound insulation, which is laid behind the panels;
• there is no need to level the walls before installation;
• the ability to dismantle the panels for use in another location.

The disadvantage of this finishing method is that it reduces the size of the room, since the lathing on which the panels are installed takes up a lot of space.

Construction of a brick partition

How to make partitions in a brick bath? This material is quite common and is often used for the construction of buildings in the bathhouse.

The construction is made using half-brick spoon masonry.

To make work easier, some specialists use hollow material.

Preparatory procedures

Before starting work, you need to carefully prepare the surface. The plank covering is removed from the floor to the very base, after which it is cleaned with a wet broom. The place where the construction will be carried out is equipped with good lighting. All foreign objects are removed from the premises and the outlines of the building are outlined.

To work you will need to prepare the following tools:

• level;
• sander;
• trowel;
• plumb line and rule;
• cement-sand mortar. For more information about the construction of a partition, watch this video:

Creating a partition

The process of erecting a brick partition consists of the following stages:

1. A string is stretched and used as a guide. The solution is laid and leveled using a trowel. The level checks horizontality. You will need to wait until the solution begins to dry.
2. Another layer is applied on top of the dried mixture. After which the first row of brick screed is laid.
3. The mortar is applied to the end of the first brick, after which it is laid by pressing down. It is tapped and leveled according to the string; the remaining mixture will need to be removed immediately before it has time to dry.
4. If an opening for a door is planned in the partition, it will need to be positioned first. The door frame is installed using spacers. The evenness of its location is checked and, if necessary, this parameter is adjusted.
5. The brick is laid close to the box. To tie the partition together, special metal strips are used; they are folded and attached to the side surfaces between the bricks. Instead of strips, you can also use reinforcing rods.
6. After laying the first row is completed, the brick is divided into 2 parts with a pick. One half is used to start the second row. The string that served as a guide is moved higher so that you can easily navigate. Laying the third row is carried out in the same way as the first. For more information about the process, watch this video:

Building any kind of partition between the steam room and the sink is a rather labor-intensive procedure.

Not every beginner will be able to do this kind of work on their own.

But, as a result, this will ensure a high level of comfort in the bathhouse, which is why the construction of such elements has recently become popular.

Also useful for repairs:

• How to knit a hat and snood with braids
• Diamond cutting wheels for metal
• DIY flowers in a dhow

Fixing drywall and finishing the surface: main steps and their description

After laying the thermal insulation, a vapor barrier is mounted on top of the racks. Its purpose is to prevent steam particles from entering the insulation. In its structure, the vapor barrier membrane is much denser than a water barrier, since it is designed for smaller particles of moisture that are able to penetrate through the plasterboard base. In addition, a ventilation gap of 1–2 cm in size is left between the vapor barrier and the gypsum board, which is necessary for its removal. To organize it, additional wooden planks are attached to the racks, to which the drywall will continue to be screwed. The installation process is as follows:

1. GCR can be fixed both horizontally and vertically.
   In this case, the installation method must be determined before applying the markings. Otherwise, its ends will not fit on the profile and will remain in an unsecured position. Fixing drywall to a wooden frame
2. Drywall is attached to the wall from top to bottom; accordingly, the bottom part of the sheet is screwed first. To secure it, 3–4 fastening points per rack are sufficient.
   Fixing plasterboard sheet to the wall

   Screwing in a screw at a distance from the edge of the sheet

3. The top sheet is installed in such a way that the distance between the wall and the ceiling surface is minimal.
   The optimal value is a gap of 5–10 mm, necessary for thermal expansion of the material. In this case, the sheets are fixed together as tightly as possible, without any gaps. There should be a gap between the ceiling and the gypsum board
4. First, the main part of the plasterboard wall is sewn up, and small parts and transitions are installed last. The finishing touch is the installation of plasterboard slopes, which marks the complete readiness of the surface.

Scheme for attaching plasterboard to the ceiling The simplest and most effective way to level the walls in a wooden house is to cover them with plasterboard. If all building codes and installation rules are followed, the new coating will serve for many years without deforming or cracking. Not the least role in this is played by finishing, designed to prepare the optimal base for wallpapering or applying any other type of decor.

An example of finishing plasterboard walls in a wooden house

Finishing the ceiling

Plasterboard is finished under wallpaper using finishing type gypsum putty. It is this material that has the necessary characteristics and makes it possible to seal any cracks, both in a new coating and to repair old finishes. It is applied and distributed with a spatula. In this case, all seams, joints and transitions are filled with reinforcing mesh and puttied with several layers of mortar. In addition, it can be used to carry out additional leveling of walls if the need arises. Excess hardened material is cleaned off with the same spatula or wiped with special grout meshes.

Beautiful examples

• Audacity and avant-garde. Walls finished with OSB without further coating create a bright interior with an interesting heterogeneous pattern. Extraordinary aesthetics are accompanied by cost savings. The fashion for such finishing is gaining momentum.
• Natural wall. Finishing the interior walls with timber-like boards allows you to create a monolithic interior with excellent aesthetics. Decorative beams are tinted in a dark contrasting color and highlight the light colors of the finish. The ceiling is covered with clapboard and painted in a light color or covered with matte varnish.

The interior decoration of a frame house is shown in the following video.