How to choose the right stretch ceiling - expert reviews

Tension fabric is the most promising material for decorating the ceiling space in an apartment or office. It provides a perfectly flat surface, has high performance characteristics and durability. Installation of a stretch ceiling is possible in renovated premises; it is carried out within 2-3 hours, does not involve wet processes and does not require a radical rearrangement of furniture. A variety of textures and colors, multi-level designs, prints and the use of special effects create unlimited possibilities for design solutions. Which canvas is better to choose? When purchasing, you should focus on the specifics of the premises, personal preferences and financial capabilities.

1. Blade type
2. Texture
3. Company manufacturer
4. Color
5. Room
6. Lamps
7. Cornice
8. Ceiling "starry sky"
9. "Floating" ceilings
10. Stretch ceilings in a country house

Differences in installation technology

As already mentioned, the properties of vinyl and fabric canvases have some features.
This is the reason for the difference in installation technology. Any PVC stretch ceiling requires heating. A gas gun is usually used for this. A stream of hot air is directed directly onto the canvas. At the same time, the room temperature rises to +60 °C. The elasticity of the film increases and it is easy to stretch it to the required size. Then a special fastener welded along the edges - a harpoon - is tucked into a profile pre-installed around the perimeter of the room. This type of fastening is used only with PVC film. Installation begins from the corner marked by the ceiling manufacturer and continues gradually in both directions along the entire perimeter.

Subsequently, as the room cools, the canvas is tensioned. For this type of ceiling, the accuracy of the measurements is especially important. Cutting the film for a stretch ceiling is carried out using special software. And the finished ceiling is approximately 20% smaller than the area of ​​the room.

Polyester, on the other hand, tends to shrink when heated. Therefore, the installation of a fabric stretch ceiling is carried out without a heat gun and preliminary cutting. A roll of the required width is unrolled right on the spot, and the excess is cut off after stretching. They begin to tuck the fabric into the baguette first on the walls (primarily on the short ones), and only then tighten the corners. Heat may be needed here - in some cases, when stretching the fabric, minor folds form in the corners. It is enough to warm them up a little with a hair dryer so that the material straightens out and acquires a smooth surface. But as a rule, experienced craftsmen do without heating.

What to look for when choosing

To get your money back for low-quality material, you will have to order an examination from the SES, and then go to court. It's long and troublesome. It is better to immediately buy a high-quality stretch ceiling.

Experts recommend:

• check hygiene certificates;
• look at photos of completed work;
• read reviews;
• pay attention to the ceilings in the office - if they are not suspended, most likely the company does not have experienced craftsmen;
• require a contract to be drawn up before payment.

A plus will be a document stating that the company is an official dealer of the manufacturer. This way the risk of counterfeiting is much lower.

Which option to choose

So which is better - fabric stretch ceiling or PVC? Perhaps the question posed in this way is not entirely correct. It is more correct to ask: “Which ceiling is best suited to a particular room?” In any case, a compromise will be required between operating conditions and personal aesthetic preferences.

The comparison table below will help you make the right choice.

Properties	Film	Textile
Strength	PVC is a tear-resistant and elastic material, but it can be easily damaged by any sharp object.	Fabric sheets are denser and stronger, practically do not stretch, and are difficult to damage mechanically.
Permissible temperature range	The film is used at temperatures from +40 to -5 °C; use in unheated rooms is unacceptable.	Fabric sheets can withstand from +80 to -50 °C; installation in unheated rooms (country houses, dachas, balconies) is allowed.
Degree of sagging over time	0 – 30 mm	0 – 10 mm
Moisture resistance	PVC is a waterproof material; when flooded from above, it can withstand up to 100 liters of liquid for a long time; after its removal, the original appearance of the film is restored; it is recommended for wet rooms.	Low moisture resistance: installation in the bathroom and kitchen is undesirable with a ceiling height of less than 2.7 m, increased requirements for ventilation. After flooding, leaks begin within 2 hours; subsequently, stains and stains that cannot be removed may remain.
Soundproofing	Absent, the film can even slightly increase the noise from neighbors, the “echo” effect.	Low, however, there are special acoustic types of fabric stretch ceilings that eliminate the “echo” effect.
Thermal insulation	Absent.	Low, it will not play a special role without additional thermal insulation materials.
Width size range	130-600 cm (European production - up to 325 cm)	150-510 cm
Installation features	Heating the canvas to 60 °C using a heat gun, increased requirements for the installation team personnel and safety measures.	Without using a heat gun.
Environmental friendliness	Safe for health and the environment.
Fire resistance	They melt and ignite if exposed to open flame for a long time.	Melts and does not support combustion.
Design	The widest possibilities for design solutions: glossy shiny, matte and satin surfaces, embossing, bright and moderate tones and shades of all colors, excellent photo printing, the ability to install multi-level, decorative perforated, translucent, transparent canvases and many other options.	A more modest range of colors, soft, soft tones, only matte texture, fabric texture with a flat surface. The small choice is compensated by a noble, even aristocratic appearance. Can be painted up to 5 times. Photo printing is also possible, but it does not look as bright.
Features of care	Easy to clean from dirt. Washing with chlorine-free detergents is acceptable; abrasive cleaning agents are unacceptable.	Fabrics are antibacterial and dirt-repellent. They can be easily cleaned only from surface contaminants.
Service life (warranty)	10-12 years	10-12 years
Price per m2	350-700 rub.	800-1500 rub.

Thus, suspended ceilings of different types, despite similar designs, have a unique set of properties and features. Which of them is the best in a particular case must be decided, taking into account the operating conditions of the room, the characteristics of the paintings and personal preferences.

Room

How to choose a suspended ceiling for the kitchen, living room, bathroom and children's room
Each room in the apartment performs certain functions. The choice of stretch ceiling for the living room, children's room, kitchen and bathroom should be made taking into account their operational characteristics.

Living room

The living room is the largest room in the apartment. All family members spend significant time here, so great attention is paid to the design of the hall. Any materials are suitable for decorating the ceiling, the main thing is that their color and texture fit harmoniously into the interior of the room. It is better to give preference to universal, calm tones that do not cause discomfort to any member of the household.

Children's

To decorate a children's room, it is advisable to choose bright fabrics. The matte surface is more durable and will eliminate the risk of damage to the ceiling by active children during games. A big plus is the presence of micropores in the fabric structure, providing natural air ventilation.

Kitchen

Cooking is accompanied by steam rising to the ceiling and grease stains settling on it. Here the best choice would be glossy PVC canvas. It has high water-repellent properties and is easy to clean.

Bathroom

The use of a bathroom is associated with temperature changes and high humidity. A glossy film ceiling is better suited for it. The canvas easily tolerates difficult conditions and can withstand a significant volume of water when flooded from above. After the accident has been eliminated, it can be installed in its original place. A glossy ceiling looks impressive in small rooms, visually enlarging the space.

Pros and cons of suspended ceilings

Advantages and disadvantages are determined by the type of coating used - PVC film or fabric ceilings.

But there are a number of common advantages:

1. Finishing speed. Films are stretched for 4-10 hours, fabric - 5-12 hours.
2. Saving the interior. Film coatings are capable of retaining large masses of water for a long time; fabric material is less waterproof, but can prevent the risk of spillage for 2-3 hours.

1. There is no need to carry out leveling work on the ceiling plane. All defects, as well as communication pipes and beams in private houses, will be covered with canvas.
2. Insulation and insulation materials can be laid under PVC and woven suspended ceilings.

Versatility. You can stretch fabrics in any room or building

It is important to choose materials that provide the desired level of comfort and meet the stated requirements for the use of space. Easy to care for. Cleaning is required no more than once every 6 months

Dry, wet cleaning is sufficient. If persistent stains appear, use conventional non-aggressive detergents.

Variability of color solutions, design formation, affordable price are additional advantages of finishing. It is also worth noting the long service life of the canvases, environmental friendliness and the possibility of using finishing in rooms with high requirements for the cleanliness of facing materials - in children's rooms, hospitals and other facilities.

The disadvantages of suspended ceilings depend on the type of fabric chosen:

• film coverings cannot be installed in open spaces in areas with a possible decrease in temperature;
• It is better not to use fabric sheets in rooms with high humidity levels;
• PVC films for ceilings are welded to be stretched over large areas;
• The maximum power of luminaires for suspended ceilings is no more than 40 watts; installation of a thermally insulating lampshade is mandatory.

When considering the pros and cons of suspended ceilings, it should be noted that it is necessary to involve a specialist to carry out the finishing. Do-it-yourself tensioning is possible, but the master will need special tools and experience, and no one can guarantee high-quality tension. It’s easier to use the services of professionals and get guarantees for all types of work.

Where are stretch ceilings used?

High-quality suspended ceilings can be used in any buildings, houses, rooms, but there are some peculiarities - films are best used in warm spaces, but woven fabrics are best used in areas with minimal moisture content, but woven materials do not deteriorate under the influence of negative temperatures.

Application area:

• private houses made of any materials;
• apartments;
• warehouse and public buildings;
• offices;
• commercial buildings;
• construction of entertainment complexes, including swimming pools, sports and concert halls;
• educational institutions and others.

There is not a single building where tension fabrics cannot be used. Fabric materials will be an ideal solution for open areas of balconies, loggias, terraces, as well as in storage rooms, basements and underground parking lots. The structures are lightweight and do not weigh down floor slabs or load-bearing beams. If the choice is made correctly, the owner receives a fireproof, environmentally friendly and aesthetic coating that will last for several decades without the need for repairs or renovation of the ceiling surface.

We evaluate the seams and texture

PVC film offers hundreds of colors, mirror and metal effects, glossy, matte, satin textures, bright images and the ability to create unusual lighting solutions. PVC sheets are either solid or welded.

They are welded when:

• the width of one strip of film is not enough to cover the required area;
• the design involves a combination of two or more colors.

Welded PVC sheets are as durable as seamless ones. To connect 2 films of different colors, they are placed on top of each other and placed under an electrode, which presses on them with a force of 600 kg. A current is passed through the films compressed with such force. Under such conditions, the films are soldered at the molecular level, and subsequently the seam is the strongest point of the PVC ceiling.

Welds are visible on monochromatic surfaces when viewed from certain angles. If you make the stretch ceiling multi-colored, no one will pay attention to the seams, because they will turn into a decorative element.

The fabric ceiling fabric consists of polyester threads impregnated with polyurethane. Simply put, it is a synthetic fabric with rubber impregnation. It looks like ordinary fabric - it seems soft and pleasant to the touch. You can order a canvas with a ready-made design or decorate it with photo printing of personally selected pictures.

Fabric ceilings are usually seamless. The seams on such surfaces are clearly visible, so they need to be presented as design elements: made symmetrical, hidden with lamps, or placed in the middle.

Note: PVC and fabric ceiling canvas with photo printing can be used to decorate walls and openings. It is mounted using the same technology as the ceiling one.

Summary: PVC canvases provide a much greater variety of colors and textures, while fabric ones allow you to avoid seams. A good seam does not weaken the structure; on the contrary, it is the strongest in this area.

Beautiful examples in the interior

The ceiling does not necessarily have to have a perfectly smooth surface. The relief and figured ceiling looks very original and stylish. In this case, aluminum slats of similar shades were used. This ceiling is resistant to high temperatures, is not afraid of moisture and provides excellent air circulation. In addition, the design is easy to maintain and will last for several decades.

The universal and most popular ceiling color is white. Beige or cream is less commonly used. But a colored or dark ceiling also looks great in some styles

But it is important to be able to combine it with the overall style of the interior.

When choosing suspended ceilings, you need to decide which option you like best - matte or glossy. A shiny, almost mirror-like gloss finish perfectly expands the space. And matte hides the seams between the canvases as much as possible. But in some cases it is not necessary to mask the seams. This can become a kind of highlight of the interior. So, for example, a satin white ceiling with black stripes looks laconic and stylish in a modern living room interior.

The ceiling can serve as a continuation of the overall concept of the room or become a unique work of art. You can apply an unusual pattern, ornament or even photographs to the surface.

If the area of ​​the apartment does not allow you to use and burden a small space with voluminous multi-level structures, and the interior style needs to be supplemented with figured and carved elements, pay attention to stretched fabrics with patterns. This is a great way to put a modern twist on the classics.

Suspended structures can look advantageous in many interior styles. And the loft is no exception. Hidden LED lighting above the suspended structure highlights the natural roughness and unevenness of the concrete floor and creates the effect of being in an industrial production room.

Fans of non-standard design solutions will appreciate ceilings that are unusual in shape and style. An option is considered stylish when the design of the hanging system is combined with shelves, niches, furniture or other decorative elements. For example, a non-standard solution is a ceiling that complements the design of a staircase in a country house.

You can watch a master class on installing a cassette ceiling in this video.

Lighting

The hall is a place where you need a lot of light, so it is necessary to arrange the structure in such a way that the lighting elements are placed usefully and beautifully. The optimal choice is a two-level design with LED spot lighting. This is a classic design for expensive and representative rooms.

Advice! A unique effect is created by continuous fiber optic illumination of the interior space.

Choosing a chandelier for the hall is also not an easy task, since it must be beautiful, but at the same time not distract attention from the splendor of the ceiling. Designers advise choosing chandeliers that have many small transparent shades, creating the effect of a starry sky.

For large luxurious rooms, you should choose classic hanging chandeliers made of crystal - in combination with a glossy ceiling, it looks majestic.

Stretch PVC ceiling

Considering what types of suspended ceilings there are, one cannot help but pay attention to PVC film materials. These are products welded from individual strips that are stretched using heat. The film itself and the air in the room heat up; after cooling, the film takes the desired shape. The texture and color scheme depend on the chosen material.

Types and characteristics

Manufacturers offer the following types of PVC films:

1. Glossy. Reflective material. You should think through the area where the weld will be placed in advance so that it is not noticeable.
2. Matte. An inexpensive type of material that does not have reflective properties, in its finished form resembles an ironed whitewashed ceiling.
3. Satin. The middle type of material between glossy and matte film. Satin fabrics reflect light, but at the same time refract and scatter the rays, which looks especially aesthetically pleasing. Satin fabrics are produced in a wide variety of colors.

The main characteristic of PVC film that influences the choice is the width of the strip, which does not exceed 5 m, therefore, when finishing spacious ceilings, the strips are welded.

The list of reliable manufacturers is small:

• Pongs, Germany. Unique seamless ceilings under the Descor brand. The thickness of the products is up to 0.3 mm, increased strength - the canvas can withstand up to 150 liters of liquid per 1 m2.
• PTCM, Belgium. The width of the canvas is 5 m, a wide choice of colors and textures. The Belgian manufacturer offers canvases with photo printing and a 3D effect. High-quality products are distinguished by their durability, resistance to dust and dirt.

There are also manufacturers from the Russian Federation, China, and Turkey. But when choosing materials, you need to request certificates of conformity and look at the description - there is a high risk of getting defective fabrics with low performance indicators.

Cost and service life

On average, the price of installation of PVC panels starts from $8-15 (600-1200 rubles) per 1m2

It is important to consider the type of material, the shape of the structure, the presence of built-in lighting and other nuances. Manufacturer's warranty 15 years, service life from 20 years

Company manufacturer

Which manufacturer of suspended ceilings is better to choose
? The quality and price of suspended ceilings are largely determined by the manufacturer. On the market you can find products made in Europe, Russia and China. Which one is better?

European stretch ceilings

Canvases from Europe occupy the largest segment of the market. Manufacturers offer a wide range of glossy and matte ceilings of the highest quality, and French companies are trendsetters. The cost of European products is significantly higher than their Russian and Chinese counterparts.

Well-known companies: Barrisol, Alkor Draka, Extenzo, Newmat, Clipso (France), Poliplast (Belgium), Renolit, Pongs, Descor, Lackfolie (Germany), Cerutti (Italy).

Russian stretch ceilings

In Russia, the production of suspended ceilings is still poorly developed. The industry leader is Saros Design, which founded production in Moscow in 1996. Today, the company has production facilities in a number of Russian cities, Kyiv, Narva, and Stuttgart. The company offers canvases in a wide range of sizes and colors, applies drawings, and makes computer calculations using its own program.

Budget buyers can choose stretch ceilings produced by the Kazan Artificial Leather Plant and Ivanovo NIIPIK. Enterprises produce canvases up to 1.4 m wide in a limited range of colors.

Chinese stretch ceilings

The range of Chinese goods is traditionally heterogeneous. Here you can find both materials that are not inferior in quality to their European counterparts, as well as outright fakes. Industry leaders include the following companies: MSD, HALEAD, Gline. Stretch ceilings from these manufacturers compete with world leaders and are much cheaper.

Glue ceiling

The adhesive finishing method involves attaching the coating directly to the base using a special glue. The most used materials for this method are panels or tiles made of polystyrene foam. These tiles are characterized by their low weight (about 0.4 kg/m2), they are easy to cut, which makes it possible to use them in rooms of non-standard shape. Polystyrene also includes properties such as heat and sound insulation. However, the disadvantages of this material are that when glued end-to-end, the panels do not form a visually solid coating. To some extent, this has become the reason for the unpopularity of this type of finishing recently. However, with the advent of glass wallpaper, the method of pasting with wallpaper came back to life. Fiberglass wallpaper is very moisture resistant. Thanks to its long service life (20 years) and the ability to be painted 10-15 times, this material occupies a leading position on the market. In addition, the adhesive method is very easy and quick to implement, and also masks unevenness, cracks and other damage to the base ceiling. The usual thickness of the coating is 10 mm, and thanks to this particular characteristic, this coating can be used in rooms where the ceiling height reaches only 2.5 - 2.6 m. But there are also some disadvantages of the adhesive method: with its help it is possible to hide only minor defects horizontally. Lighting options are also limited: the use of built-in lighting is excluded, it is impossible to “disguise” any technical equipment, including electrical wiring. As for the purchase price for this type of finish, it depends directly on the material you choose. As an example, the price of foreign-made tiles fluctuates around 175 rubles per sq. m. The average cost of domestic polystyrene panels, especially non-laminated ones, is 15 rubles. per sq.m.

Choosing a color for apartment ceilings

Today's diverse design options allow you to create the most incredible types of ceilings in your apartment. They are the simplest, monochromatic and representing one plane. This option is ideal for minimalism - it is often done in light shades. Such light ceilings are ideal for all style decisions. But sometimes situations arise when you want to add some variety, or the design requires original solutions.

The ceiling is often decorated with additional decorative elements.

If you want to experiment with color, then you should consider the basic rules:

• if the room has a low ceiling, then you should use the lightest colors possible without complex designs;
• when there is a low level of natural light, you should make a multi-level ceiling that is as light in color as possible, integrating spotlights into it;
• if you use color on this part of the room, then it should be in harmony with the overall color scheme.

By designing this type of ceiling, you can easily hide any unevenness and imperfections on the ceiling surface.

What to choose for the hall?

In comparison with painted ceilings, stretch ceilings are more variable in terms of decoration - they can be made in color, with photo printing, lighting, installed in several levels and connected to plasterboard structures.

Speaking about the base materials for such a ceiling, we can distinguish two main types:

Base type	Varieties	Properties
Film	Glossy, matte, satin	They stretch well, do not burn, are not susceptible to fungal infections, and are fragile when temperatures change.
Fabric	Smooth, embossed	They do not stretch, are more durable, and are not afraid of temperature changes.

The living room is a place where you can use modern materials to the maximum - both the space allows, and you want to make the interior of the room as rich and impressive as possible. By the way, different textures are quite compatible with each other, so the scope for creativity and inspiration is almost limitless.

Now let’s take a closer look at how these materials can be used specifically for the ceiling in the hall.

Designer tips for choosing a ceiling for an apartment

When choosing a ceiling finish, you need to rely not only on your preferences, but also on the basic requirements that apply to this part of the room. Depending on the style decision, it is worth choosing the finishing material and color.

The larger the area of ​​a single room and the entire home as a whole, the more experiments with decoration you can afford.

In a studio room, it is advisable to use the ceiling to zone the space. If, for example, you create a difference between the dining area and the living area or use different materials, then you can visually divide the room into two parts.

A wide range of finishing options in construction stores will allow you to easily bring to life the most daring design ideas and choose the right solution for any budget.

In any case, before you begin to implement any of your own plans, it is advisable to draw a sketch of the entire room with a certain type of ceiling. If your hand is not positioned sufficiently and you cannot create a sketch, then it is better to turn to a professional designer for it.

Options for fastening the canvas

A stretch ceiling cannot be fixed with nails, screws or anything similar - the fabric or film will be damaged. A special frame is made from a profile to which the canvas is attached.

Aluminum or plastic is used to make fasteners. The first is required for large rooms (from 50 square meters), as it better withstands strong tension. Both options are suitable for medium and small rooms.

Several types of fastening of suspended ceilings have been developed, differing in shape and design:

• harpoon;
• wedge or glazing bead;
• clip-on

Harpoon

With such a fastening system, an accurate calculation of the area of ​​​​the future ceiling and preliminary preparation of the canvas are required. A special plastic edge is welded to the edge of the PVC film - a harpoon, which is then inserted into the hole of the baguette.

This installation method allows you to remove the film and attach it back. This makes it easier to access the space behind the ceiling. There may be lighting fixtures, generators and converters, air ducts, etc. The film is also removed in order to drain water after a flood.

Beading

Wedge and glazing bead fastenings are similar to each other. The film is cut with a margin (about 7-13%). The edges are inserted into the profile holes and secured with a plug. The part is produced in the form of a wedge or bead. The name is determined depending on the type.

With this method, excess fabric remains at the edges, which is cut off or hidden behind a soft ceiling plinth. Installation is simplified, since no preliminary preparation is required, and the calculation may not be as accurate. But the removed film cannot be reattached.

Clip-on

For fabric ceilings, a clip fastening is used, which is also called “cam” or “Clipso”. The fixation acts like a clothespin into which the edge of the canvas is inserted.

Kinds

Two-level ceilings are a modern way to make the interior unique and original. With the help of building and finishing materials, you can achieve more than two levels of height. And at the same time, any design, in addition to aesthetics, has additional practical characteristics. But such multi-level structures look good only in spacious apartments.

There are several types of suspended ceilings:

Tension is perhaps the most popular finishing option. Fabric or PVC film with a minimum thickness is used. The surface does not require careful maintenance; it is enough to periodically wet clean it with a soft cloth to get rid of dust and dirt.

Each type of suspended ceiling is typical for certain types of premises. A wide variety of materials, designs, sizes and colors allows you to choose the ideal option for your apartment or house.

What should be the height

Finishing the ceiling with a suspended structure requires at least a small frame. This will make the space of the room visually noticeably smaller. The design of a suspended ceiling is simple: using a frame system made of metal profiles or wooden beams, the canvas and various elements of the future covering are attached to the main partition. Decorative panels and all parts on a metal grille are attached to the installed hangers. Correct installation of guides and support profiles ensures easy installation. And with the most minimal installation option, the distance between the ceiling and the suspended ceiling will be at least 3 cm.

The ceiling installation height is also affected by some individual reasons:

Built-in lamps may have a large body, which will need to be hidden behind the ceiling structure. If desired, you can install an LED strip or a simple chandelier into the ceiling structure. It is also necessary to take into account the dimensions of the housing, which will be hidden behind the insulating material.

Rules for installing cornices

When installing a stretch ceiling, it is important to remember about curtain rods. There are wall and ceiling structures. The latter are more attractive; they are mounted using open or hidden installation.

When installed hidden, the structure is attached to the ceiling above the level of the canvas itself. A beam or corner is fixed nearby to install the guide molding. The procedure is done before taking measurements. Curtains falling from the ceiling look more interesting. This installation is well suited for both matte and glossy ceilings.

Before installing the canvas, a wooden beam with guide profiles is attached to the ceiling. Designers recommend choosing hardwood (birch is suitable). Before use, the timber is treated with an antiseptic solution. After installation of the structure is completed, the cornice is attached to the wooden beam through the film.

Stretch or suspended ceilings

For those who have not yet decided for themselves which is better - a suspended ceiling or a suspended one, we will try to make the task easier through a brief comparative analysis:

• Stretch ceilings are good, first of all, for their irresistible appearance and comparative speed of installation, but installation can only be carried out with the involvement of third-party specialists due to the complexity of the technology (see Advantages of stretch ceilings: again about the good).
• Suspended ceilings can be installed independently, and they have virtually no restrictions on complexity. However, they cannot boast, for example, of the ideal gloss inherent only to film stretch fabrics (see Aluminum suspended ceilings - types, scope, installation features).

Combination of a suspended ceiling with a suspended ceiling in a two-level ceiling structure

• When determining which is better - a suspended or suspended ceiling, in each specific case you should take into account the characteristics of the room. Thus, stretch ceilings are usually used for luxury modern interiors, but, for example, they are not suitable for outdoor rooms and rooms without heating, since they become brittle at low temperatures, which cannot be said about suspended systems.
• It is advisable to use suspended ceilings in the decoration of large premises - offices and other institutions; moreover, such systems look more strict.

Lamps

What lamps for suspended ceilings are best to buy?

Stretch ceilings are ideal for built-in lighting. When choosing them, you should take into account the operational characteristics of the material and temperature restrictions: if the standard values ​​are exceeded, the canvas will warp.

Incandescent lamps

The use of classic lamps with a tungsten spiral in tension structures has the greatest limitations associated with their high heating:

• power up to 40 W for film ceilings, 60 W for fabric ceilings;
• the ventilation gap between the canvas and the ceiling is at least 12 cm.

Incandescent lamps are attractive due to their low price, but have a short service life: about 1000 hours.

Halogen lamps

When installing halogen lamps, the following standards must be observed:

• power up to 20 W for film ceilings, 35 W for fabric ceilings;
• ventilation gap – 6 cm.

Compared to incandescent lamps, they emit brighter light in the yellow spectrum and have a resource of 2-4 thousand hours. Halogen lamps are best used for directional illumination of work areas.

LED bulbs

LED lamps practically do not heat up and have no restrictions for installation. This is the best option for suspended ceilings. LED lamps can be chosen both as the main light source and to create visual effects on matte, satin or glossy canvases. Lamps of this type are the most economical, and their service life is about 5 years.