Putty Rotband paste Knauf Knauf Rotband Pasta 18kg

What is Rotband paste?

Until recently, cement or limestone was used as plaster. But none of them gave the desired result either in the speed of hardening or in service life. Thus, the cement hardened quickly, but cracked just as quickly. And the lime mixture took a long time to harden. Therefore, with the advent of gypsum, all these problems were solved. It has become an ideal material for puttying walls. One of the first companies to begin producing gypsum putty was.

"Rotband" is a paste designed for filling small unevenness on the wall. Thanks to its composition, it can be used both as a starting putty and as an addition to it. This mixture can also be applied as an auxiliary layer over plaster.

Rotband paste is often used in areas of high humidity, for example, in the bathroom. The mixture is also used for polystyrene foam surfaces and other types of wall coverings.

Putty Knauf Rotband Paste Pro for finishing puttying of surfaces and joints 5 kg

Description:

Ready-made paste-like vinyl-based finishing putty. It has increased whiteness, adhesion and crack resistance. Ideal for thin-layer (scraping) puttying of surfaces. Thanks to its high plasticity, it is easily leveled and perfectly fills all small irregularities. After drying, the surface is ready for finishing with paint or wallpaper.

Application area:

Knauf Rotband Paste PROFI is a ready-made paste-like finishing putty on a vinyl base. It has increased whiteness, adhesion and crack resistance. It is used indoors for finishing puttying of the surface of plasterboard or gypsum fiber sheets, plastered and concrete surfaces, tongue-and-groove slabs, fiberglass in preparation for high-quality painting, wallpapering, before applying Venetian plaster and other finishing materials.

Features of the KNAUF Rotband-Paste building mixture:

• The material is sold in completely finished form, so additional work on mixing the solution is not necessary;
• It is also not necessary to maintain a certain time for the solution to mature, since the mixture is completely formed;
• Has a very elastic structure;
• Densely fills joints and defects of the base surface;
• Has a short drying period;
• Subsequent grinding is welcome, it is easy, the material is quickly leveled;
• Quickly and efficiently attaches to the base;
• The degree of whiteness after drying is very high.

Application of KNAUF Rotband-Paste putty:

Finishing putty is sold in ready-made form. It has a polymer base and is indicated for use only indoors and in buildings.

Application area:

• For finishing puttying of joints and surfaces of plasterboard sheets;
• For puttying concrete and already plastered walls and ceilings, followed by recommended gluing and painting with decorative materials;
• For sealing joints between sheets of plasterboard, the edges of which can be either thinned or straight cut. In this case, the use of reinforcing tape is mandatory.

More information about the KNAUF Rotband-Paste building mixture:

Remember that contraindications to the use of the Rotband-paste putty mixture are plasterboard sound-absorbing sheets with a perforated surface, as well as joints between these building elements.

Peculiarities

Rotband paste has the following features:

• increased adhesion to the wall, which prevents the appearance of cracks in the future;
• good plasticity, allowing to remove all surface irregularities;
• quick drying;
• low level of thermal conductivity and sound conductivity;
• good moisture absorption, without the possibility of cracking.

In addition to the above, the paste does not crumble during grinding. But the main feature of the Rotband mixture is that it contains a limestone filler, which gives it plasticity. After treating the walls with this paste, you can immediately begin painting or wallpapering. This material can also be used to seal joints, and with the help of reinforced tape you can also hide unevenness between sheets of drywall.

According to the recommendation of experts, Rodband paste should be applied in a layer of no more than 10 mm, although this does not prevent the layer thickness from being increased if necessary. But in this case, the work will have to be carried out in several stages in order to avoid the plaster falling off. It is not recommended to make the thickness more than 50 mm; in this case, it is better to cover the walls with plasterboard.

Rotband mixtures: Profi paste

This mixture is supplied in plastic buckets weighing from 5 to 18 kg, depending on the amount of work required. Has a pasty appearance. Its main area of ​​application is leveling walls and decorating them.

Supplied mainly in white, but other options are also possible. The advantage of this paste is its resistance to frost, which makes it possible to transport it in the cold season. Even when completely frozen, the paste does not lose its properties.

Distinctive features of the “Pro” paste are:

• adhesion (high grip);
• greater thickness than regular paste;
• resistance to frost;
• dense consistency;
• longer shelf life (9 to 12 months).

Due to its plasticity, the paste is ideal for final puttying of walls. It saves not only time, but also money. But to work with this mixture you need to know a few rules:

1. Before application, the surface must be cleaned of dirt.
2. Widen the cracks for better bonding.
3. After puttying, sand the surface.

Knauf Rotband Pro paste is used mainly for applying thin-layer putty.

LKMFLOT

Code: 100991923

Category:
Putties and Plasters
Brand:
Knauf
Packing:
5, 18
Packing:
1
Ready-made finishing putty Knauf Rotband Pasta Profi - Ready-made paste-like finishing putty on a vinyl base. Ideal for thin-layer (scraping) puttying of surfaces. Thanks to its high plasticity, it is easily leveled and perfectly fills all small irregularities. After drying, the surface is ready for finishing with paint or wallpaper.

AREA OF APPLICATION Knauf Rotband Paste PROFI is a ready-made paste-like finishing putty on a vinyl base. It has increased whiteness, adhesion and crack resistance. Ideal for thin-layer (scraping) puttying of surfaces. Thanks to its high plasticity, it is easily leveled and perfectly fills all small irregularities. After drying, the surface is ready for finishing with paint or wallpaper. It is used indoors for finishing puttying of the surface of plasterboard or gypsum fiber sheets, plastered and concrete surfaces, tongue-and-groove slabs, fiberglass in preparation for high-quality painting, wallpapering, before applying Venetian plaster and other finishing materials.

ADVANTAGES • increased whiteness • high crack resistance • optimal ductility • high adhesion • does not chalk • withstands repeated freezing

TECHNICAL CHARACTERISTICS Layer thickness: up to 2 mm Grain size (average): 40 microns Operating temperature: 10-30°C Drying time: 24 hours Freezing / thawing: min. 5 cycles

MATERIAL CONSUMPTION Material consumption Consumption of putty mixture for continuous puttying of the surface and a layer thickness of 0.3 mm

PACKAGING AND STORAGE Putty is packaged in 18 and 5 kg buckets. Protect packaging from direct sunlight. Store in cool, dry rooms at positive temperatures away from heating devices. When freezing, do not accelerate thawing using heating devices or hot water, this will lead to damage to the putty. Defrost at room temperature for 1-2 days. After defrosting, do not drain the water formed on the surface of the putty! Otherwise, the working properties of the material will not be restored. Before use, mix the putty thoroughly with a mixer at minimum speed without adding water until it has a homogeneous consistency. The putty can withstand repeated freezing/thawing in unopened and undamaged packaging. Shelf life in unopened and undamaged packaging is 12 months.

PROCEDURE OF WORK PREPARATION OF THE BASE The temperature of the putty, base and air in the room should not be less than +10°C. Gypsum board sheets must be firmly mounted on the supporting frame. Plaster and concrete bases must be smooth, dry, free of dust, dirt and peeling. Large unevenness or damage must be leveled using KNAUF-Fugen mixture and dried. No surface priming is required.

OPERATION PROCEDURE Before starting work, stir the mixture. If necessary, add a little water (no more than 30 ml per 1 kg) and mix again. ATTENTION! Excessive dilution of the putty with water can lead to severe shrinkage and reduced adhesion. For work, use clean stainless steel containers and tools.

CONTINUOUS PUTTY - apply a layer of putty up to 2 mm thick manually or mechanically - smooth the putty with a spatula - sand the surfaces after drying, for example, with P240 sandpaper or finer grain - remove dust. Apply the next layer after the previous one has completely dried. Rinse containers and tools with water immediately after use.

DRYING TIME At an air temperature of +20°C, air humidity of 60% and a layer of putty of 1.5 mm is 24 hours. Drying time may vary depending on temperature, humidity and layer thickness. To speed up drying, it is not allowed to point heat guns, etc. at the treated surface.

PACKING 5 kg, 18 kg

Paste "Rotband Finish"

The Knauf finishing putty contains a polymer mixture with marble flour. The paste is applied not only to already plastered surfaces, but also to cement blocks and drywall. This putty is environmentally friendly and does not emit substances harmful to the body.

“Rotband Finish” is distinguished by the following parameters:

• white walls after application;
• high elasticity;
• ease of application;
• good adhesion with other materials;
• absence of odors;
• the ability to store leftover putty for a long time.

Perfect finish

KNAUF-Rotband Pasta Pro – preparing walls for painting

Ready-made paste-like finishing putty on a vinyl base KNAUF-Rotband Paste Profi has increased whiteness, adhesion and crack resistance. Ideal for thin-layer (scraping) puttying of surfaces. Thanks to its high plasticity, it is easily leveled and perfectly fills all small irregularities. After drying, the surface is ready for finishing with paint or wallpaper.

Application of finishing putty KNAUF-Rotband Pasta Profi

It is used indoors for finishing puttying of the surface of plasterboard or gypsum fiber sheets, plastered and concrete surfaces, tongue-and-groove slabs, fiberglass in preparation for high-quality painting, wallpapering, before applying Venetian plaster and other finishing materials.

Preparing the base before applying KNAUF-Rotband Paste Profi

The temperature of the putty, base and air in the room should not be less than +10 °C. Plasterboard sheets must be firmly mounted on the supporting frame. Plaster and concrete bases must be level, dry, free of dust, dirt and peeling. Large unevenness or damage must be leveled using KNAUF-Fugen mixture and dried.

Preparation and application of Pasta Profi putty

Stir the mixture before starting work. If necessary, add a little water (no more than 30 ml per 1 kg) and mix again. Excessive dilution of the putty with water can lead to severe shrinkage and reduced adhesion. For work, use clean stainless steel containers and tools.

Complete puttying of the wall surface

• Apply a layer of putty up to 2 mm thick manually or mechanically.
• Smooth out the putty with an even spatula.
• Sand the surfaces after drying, for example with P240 or finer sandpaper.
• After sanding, remove dust.
• Apply the next layer after the previous one has completely dried. Rinse containers and tools with water immediately after use.

Drying time for Knauf finishing putty

At an air temperature of +20 °C, air humidity of 60% and a layer of putty of 1.5 mm - 24 hours. Drying time may vary depending on temperature, humidity and layer thickness. It is not allowed to direct heat guns, etc., onto the treated surface to speed up drying.

Sincerely,

Internet Marketing Team

#Building materials for professionals

Use of material

Rotband paste is applied in several ways:

1. The solution must be applied to the walls with a large spatula in small quantities from the bottom up. The tool should be pressed as firmly as possible against the wall. Repeat the action several times. It is very important to ensure that there are no holes or streaks left after application. This method helps to achieve a flat surface. After applying the putty, you should go over the surface with a sanding machine.
2. This method involves applying the paste twice to the wall in small strokes over the entire surface. This will reduce the need for additional sanding.

Putty is a leader in the construction market and confidently holds this position from year to year. The company's products have gained a strong position due to their quality, large assortment and low prices.

Delivery by our transport is carried out in Moscow and the Moscow region

In this case, payment can be in two ways:

Payment upon delivery (This will allow you to be convinced of the proper quality of our building materials, and then make a payment to our driver)

Payment by card (If the transfer is planned upon delivery of building materials, in this case we take an advance payment equal to the delivery amount and + 1% commission for withdrawing money)

Prices for delivery of building materials in Moscow:

Prices for delivery of building materials in the Moscow region:

We also provide services:

Unloading on the ground 0.5 rubles per 1 kg

Lifting of Drywall, Profile, OSB, and other dimensional Materials are calculated separately with the manager

Return Policy

• Returns are made within 14 days from the date of purchase. The goods are delivered to the shipping warehouse (check with managers) or you can use the delivery and loading service. Price according to price or individually.
• Products sold by the meter (measured, cut), damaged, expired, or in poor presentation are not subject to return.

When unloading and lifting, cleaning the entrance, removing garbage and other ensuing consequences after lifting the building material are not included in the price. Prepare in advance for the service you ordered. Thanks for understanding !