The kitchen is the most working and frequently used room in the house. Here they prepare food, have breakfast, lunch, dinner, and communicate with family and close friends. At the same time, the kitchen is the most technologically advanced room in the house, and half of the appliances in the kitchen are connected to all kinds of communications: gas and water pipes, exhaust ducts, heating and sewage pipes.
We welcome our regular reader! Our article talks about how to hide pipes in the kitchen. Many pipes do not fit into our concept of aesthetics; they collect dust and soot, giving the kitchen a sloppy and somewhat disordered look.
Kitchen interier
The owners pay a lot of attention to the interior of the kitchen, carefully selecting furniture, curtains and dishes. But don't forget about the pipes. To prevent them from spoiling the appearance of the kitchen, you need to disguise them.
While some pipes can be hidden in the wall, others cannot be hidden this way. You don't want to dismantle the wall to clean out the sewer pipe, do you?
There are many methods of camouflage. There are very simple ones, they do not require large expenses and the help of specialists. But there are also complex ones that only an experienced master can handle.
When choosing one of the camouflage methods, you should weigh all the pros and cons and choose the only correct option.
In this article we will present you with photo instructions on how to hide pipes in the kitchen and consider in detail the methods of camouflage.
The law is harsh...
Household gas is a source of increased danger, or rather an explosion hazard. Moreover, not only you and your home can suffer, but also your neighbors and the whole house. Therefore, everything related to gas is subject to strict regulation. For violating the rules there is a very serious fine.
SNiP 42-01-2002 specifies the technical requirements for the operation of the gas pipeline. What is important for us here:
- all gas equipment, including pipes, must be open and accessible for inspection;
- it is not allowed to close the pipeline hermetically;
- various structures covering the gas pipeline must be easily removable and not impede air circulation. There should be no load on the pipe, i.e. You can't attach anything to it.
Why hide pipes?
A large number of pipes in the kitchen greatly spoils the appearance and visually reduces the space. They will ruin even the most expensive repairs, and even if they place the furniture the way they wanted, it will cause harm.
That is why the owners are tormented by the question: how to disguise communications in the kitchen? This problem is quite common and very easy to solve. All you have to do is contact a special company and choose a masking method.
Important Rules
Anyone who is going to hide communications must take into account one important rule.
This means that the gas pipeline can only be hidden with removable structures, for example, a special casing or fire-resistant plasterboard box. But it is prohibited to hide it in grooves or in the thickness of the wall.
Depending on the style of the kitchen, you can use the equipment in different ways.
Such a box should be easily and quickly removed to allow inspection and repair of gas services.
If communications could be transferred, then perhaps the problem would be solved much easier. But such a service is often expensive, and permission for it is very rarely issued.
Related article: How to fix a cable duct on a concrete wall
How to hide a gas pipe in the kitchen: popular methods
Without gas pipes, a kitchen cannot exist. They run through the middle of the main wall and do not look aesthetically pleasing. To give the kitchen space beauty and not spoil the interior with pipes, you need to hide them.
The issue of masking gas pipes is the most pressing. We all understand perfectly well that putting them away in a wall or hiding them in an inaccessible place is strictly prohibited.
But today there are several simple methods of disguise that you will definitely like. So, the gas pipe can be hidden in
- Korobe . It can be made from a variety of materials;
- Decorate with various beautiful and unusual things;
- Closet . The simplest and most expensive method of disguise.
Use of kitchen furniture
Marking the pipeline and gas meter behind furniture facades requires much larger capital investments.
It is necessary to develop the design of the kitchen unit in such a way that vertical pencil cases and hanging cabinets are located in the appropriate places and heights. At the same time, the interior space of the cabinet can be used for storing utensils.
How to hide the pipe from the hood in the kitchen easily and quickly
The hood has long become a necessary element of the kitchen. This functional item purifies the room air from unpleasant odors and eliminates excessive moisture.
There are several ways to hide the corrugation from prying eyes, but the most popular are: Plastic box; Metal box; Plasterboard box; Upper cabinets; Multi-level ceiling.
There are also pipes leading to the hood, which must be hidden so that they are not conspicuous and do not spoil the appearance of your favorite room.
Instructions for constructing a plasterboard box
First of all, marking of the future cladding is carried out. To do this, measure the passage of pipes, marking the contours of the future box on the walls, floor and ceiling.
Required tools and material
To work you will need:
- laser level or plumb line;
- pencil or marker;
- roulette;
- square;
- electric drill;
- screwdriver
Before starting work, building materials and fasteners are purchased. To make the box you will need:
- metallic profile;
- plasterboard sheets;
- dowels;
- screws;
- paper perforated reinforcing tape;
- putty mixture for drywall.
The amount of material required is determined using accurate measurements and calculation of the dimensions of the future box.
Preparing the work site
In the area where the metal profile is installed, all interior decoration is removed: wallpaper, ceramic tiles, suspended and suspended ceilings. The surface of the base is carefully leveled, construction debris and dust are removed.
Calculation of box dimensions
The pipes should not be closely adjacent to the sheathing sheets, therefore, during installation, leave the necessary gaps, about 2 cm. The contours of the inner border of the box are applied using a laser level or plumb line. The final cross-sectional dimensions are determined depending on the width of the profile used and the thickness of the skin.
For example, the width of the box will be equal to the distance from the wall to the extreme border of the riser + a gap of 2 cm + profile width + thickness of the drywall sheet. Depth is measured in the same way. The height of the box is equal to the height of the room, since the installation of the profile is carried out not only on the walls and floor, but also on the ceiling (floor slabs).
Frame
The frame of the box is made of galvanized metal profile . A U-shaped guide profile (PN) is mounted along the floor and ceiling . Ceiling (PP) or more powerful C-shaped rack profile (PS) is used as racks.
The size of the profiles must correspond to each other, that is, a paired guide profile PN (28x27) is selected for the ceiling structure PP (60x27), and a guide PN (50x40) is selected for the rack-mount PS (50x50). The larger the profile size, the thicker the skin will be. Standard length is from 2750 to 4500 mm.
PN profiles serve as guides for racks, that is, PP or PS structures are inserted into the PN. The pitch of the racks is 600 mm. If the largest side of the box exceeds this size, install an additional stand. In the case of subsequent lining of the box with ceramic tiles, the pitch of the racks is made no more than 400 mm.
The height of the rack profiles is made 10 mm lower than the height of the room, and in earthquake-prone areas - 20 mm. To install hatches, lattice screens or ventilation grilles between the racks, jumpers are made from the PN profile.
Such structures are fastened to the load-bearing base using dowels, through a special sealing tape or sealant. For this purpose, ready-made holes with a diameter of 8 mm are provided in the guide profiles. The fastening pitch is no more than 1000 mm, but not less than 3 dowels per 1 profile.
Plasterboard sheathing
Drywall sheets are divided into 4 groups:
- GKL - ordinary, for rooms with dry and normal humidity conditions.
- GKLV - moisture resistant with low water absorption (less than 10%), for rooms with dry, normal, damp and wet humidity conditions.
- GKLO - with increased fire resistance, for fire hazardous premises.
- GKLVO - moisture resistant with increased fire resistance.
The cheapest are gypsum boards, so many people use these sheets. For the kitchen, especially for lining pipes, it is better to use moisture-resistant plasterboard GKLV. It is very easy to distinguish it from the usual one: such sheets are green instead of gray.
Standard sizes of plasterboard sheets: length - from 2000 to 4000 mm in increments of 50 mm, width - 600 or 1200 mm, thickness - from 6.5 mm to 24 mm. For the construction of boxes and wall cladding, sheets of medium thickness, 12.5 mm each, are usually used. They have different longitudinal edges, on which the reliability of the joint and the price depend. In the case of a small box, the type of edge does not matter much.
Plasterboard sheets are attached to the frame with screws at intervals of 250 mm. The distance from the screw to the longitudinal edge of the sheet is at least 10 mm, to the end edge - at least 15 mm. The vertical displacement of screws on two adjacent sheets must be at least 10 mm. The screws are tightened strictly at right angles, the cap is recessed to a depth of about 1 mm for further putty. On the inside of the box, the screw must protrude beyond the plane of the profile by at least 10 mm.
Vertical joining of sheets is carried out only along rack profiles. The lower border of the sheathing is not brought to the floor by 10 mm. This gap is sealed with putty or acrylic sealant. Where the plasterboard joins the walls, a separating tape is glued, the excess of which is then cut off during puttying.
In places where water supply and heating pipelines with a diameter of up to 60 mm pass through, sleeves made of fireproof materials are installed in the casing. For diameters greater than 60 mm, casings are used.
Seam processing, putty and finishing
In order to perform a high-quality finishing of the box (wallpapering, painting, etc.), the seams are treated and the surface of the sheathing is puttied.
Procedure:
- the joint is removed from dust;
- apply the first layer of putty by pressing perforated paper reinforcing tape into it using a spatula;
- after the first layer has dried, apply the second;
- After it dries, a finishing leveling layer is added.
The outer corner of the box is strengthened using a corner perforated profile made of galvanized steel (PU 31x31x0.4 mm), a protective aluminum profile (25x15x0.5 mm) or aluminized Alux tape. They are also pressed into the putty mixture, after which a leveling layer of putty is applied.
Important! When using moisture-resistant plasterboard sheets (GKLV), a moisture-resistant putty mixture is used.
Next, the finishing of the box is performed. Drywall sheets are painted with water-dispersion paints. The use of liquid glass or lime-based paints is prohibited. Any wallpaper is suitable.
Multi-level ceiling
Stretch ceilings look very beautiful in rooms of different sizes. If you have one in your kitchen or are planning to make one, then the corrugation can be hidden in the stretch ceiling.
The hood pipe can quickly become clogged and will have to be cleaned. In this case, the suspended ceiling will have to be disassembled to fix the problem. And only a master can restore the ceiling, and this is an additional cost.
Coloring
In this case, there is no need to talk about “hiding”. The pipe will still be visible. But this drawback of the kitchen can be partially mitigated if you choose the right paint color. Here the owner’s “hands are not tied.”
In production, gas lines are necessarily painted yellow. In relation to housing, there are no GOSTs, norms or rules. The owners choose the color themselves. Naturally, focusing on the overall design of the kitchen. Therefore, we can only recommend the technique, but not the shade. By the way, in some cases this is almost the only rational way to hide a gas main pipe, so you should not reject it a priori. As a rule, the paint color is selected in accordance with the tone of the surface. However, playing with contrasts is also a pretty good and original solution.
Advice - when cleaning a pipe from old paint and rust, you should not use power tools. The operation of a grinder or angle grinder is accompanied by strong heating of the material. There is no need to explain what this means for a metal pipeline, which is also a gas pipeline.
Closet
A closet can be considered the easiest way to disguise. It is very convenient to use and does not spoil the appearance.
In addition, such cabinets can be used as additional compartments for storing dishes or kitchen textiles.
With paint
One of the simplest and most inexpensive ways is to paint the gas pipe in the same color as the walls, or vice versa, in a bright contrasting color.
To ensure an ideal result, use paints designed for painting pipes, which, in addition to the aesthetic component, protect metal pipes from corrosion.
How to hide boiler pipes in the kitchen so that they are always visible
You can hide the pipes coming from the boiler and to the boiler in a closet or a special nightstand. They do not have a back wall and are easy to install. Furniture is made to order and strictly according to individual drawings. Therefore, the cost of such camouflage can cost a pretty penny.
This method is considered one of the most convenient. The owners will always be aware of the condition of the pipes and, if the need arises, they will promptly fix the breakdown.
Examination
Upon completion of all installation work, the entire system is checked for leaks and general performance.
In general, you need to check the following questions:
- The system is ready to function, that is, everything must be tightened, everything connected, and so on;
- No fuel leakage in all components and connections.
The test is carried out the old way - using a regular soap solution. It is applied with a brush to all connections. If bubbles appear after application, then we can say that there is a leak. This connection is made poorly and requires reworking.
It should also be noted that all changes are made to the premises passport. Contributions can be made only on the basis of the act, which was discussed a little higher.
A blue flame can bring comfort and coziness to every home. Not a single housewife who prepares food can do without it. However, the use of gas is often associated with risk, and the safety of all its inhabitants depends on how competently the installation of the gas system in the house is carried out. That is why the transfer of gas pipes and all other installation work of the gas supply system is best left to professionals.
Photo example of options for hiding pipes in the kitchen
Did you like the article?
Use textiles, cords, twines
Using a rope or rope, wrap the gas pipe after covering it with glue.
For beauty, you can weave or glue various decorative elements - plastic flowers or leaves, rhinestones and beads, shells brought from the sea. This method is suitable for interiors in country or eco-style.
Coffee makers and coffee machines: modern equipment for business, home and office- What to consider when buying a coffee machine
- Ventilation grilles
Another natural material is bamboo. Here's how to hide a gas pipe using it. Select a bamboo stick with an inner diameter slightly larger than the diameter of the gas pipe, cut it lengthwise and wrap it around the gas pipe. The result will impress you.
Detailed description of the work
Step 1. Give the pipe the desired background. Paint in your chosen colors. After complete drying, the subsequent finishing begins.
Step 2. Cut out the motifs you like, separate the top layer of the napkin with the pattern. First apply it to the place and apply marks.
Step 3. Coat the cleaned, degreased surface with glue. Apply the design and secure on top with another layer of glue. For decoupage, use an adhesive-based mixture diluted with water in the ratio: 2 parts PVA + 1 part water. The completely decorated pipe is left for several hours and allowed to dry thoroughly.
Step 4. Apply several layers of varnish on top, allowing each layer to dry. The number of layers is from 2 to 10. This surface is easy to clean and the pattern is not distorted.
Decorating using decoupage technique
The decoration made using the decoupage technique looks elegant and original. This technique for fabric or furniture involves cutting out various images. Pictures made of fabric, paper or leather are applied to the surface of the pipe. This design will help give the room design a bright and unusual accent.
Heating pipes under the baseboard
Before decoration, the batteries are processed. They are cleaned and processed with sandpaper. The battery is then coated with enamel paint. It is necessary to measure the length and width of the pipe. After this, you can start cutting out various images.
Decoration of pipes with metal profiles
It is better to glue the fragments using PVA glue. If the image is securely fixed, then it can be coated with varnish on top. The drawing can be of a wide variety of subjects. The main thing is that it fits well into the design of the room. By the way, you can involve children in decorating the pipe. The decor will be bright, original and cozy.
Pipe decor with shells
Furniture facades
It is permissible to cover the vertical and horizontal parts of the pipe and gas supply meters with elements of the kitchen facade.
When replacing furniture, it is recommended to order an imitation facade. It’s easy to use existing furniture.
An indispensable condition for compliance with safety requirements is to equip the cabinet with ventilation grilles in secluded places.
The advantage of the bottom method is that it provides easy access to gas communications.
