Let's figure out how and what to paint slopes with: expert advice

Section Contents

1. Standard colors for sandwich panels 2. Non-standard colors for sandwich panels 3. Single-sided sandwich panels 4. Recommendations for choosing colors 5. Choosing colors for an organization
Classification of sandwich panels by color according to the RAL catalog is a standardized list of shades of a polymer coating that is applied to the metal cladding of the panel and, in fact, is the finishing layer of the “sandwich”.

According to the RAL color system, each shade is assigned a four-digit number. The first number indicates the main color, and the next three indicate the specific shade of the coating.

Let's start painting

Regardless of the type of surface you plan to paint, use masking tape to seal the frame first. To do this, cut a strip equal to the length of the frame and carefully glue it. It is important to do this as evenly as possible to prevent staining of the frame, since after this it is almost impossible to wash it. Also, before work, prepare a container for paint - check whether the roller fits it and whether it will be convenient for you to work. After that, you can pour dye into it.

Painting drywall trim

After preparing the paint and putting on rubber gloves, you can begin painting. To do this, follow the step-by-step instructions:

1. To do this, you first need to paint hard-to-reach places and joints, corners with a brush. It is recommended to use a brush that is not too wide for this; you need to base it on the standard width of your slopes.
2. After painting the corners, use a roller to paint the main part of the wall. You should not go over one place several times with a roller, since due to the glossy surface, this can only spoil the aesthetics of the paint - it will form smudges and stains.
3. Let the first layer dry. This will take from ten to twenty minutes, depending on the thickness of the layer you apply. After this, you can apply a second layer according to the same scheme - first hard-to-reach places with a brush, and then the main part with a roller. It is recommended to do this in one or two touches of the roller to one place so that the dye spreads evenly.

Standard colors according to the RAL catalog

There is no markup for these colors.

Below are 14 standard colors for sandwich panels according to the RAL catalog.

Production times for any of these colors are standard.

The availability of the required color in production, in order to speed up the process, you can check by phone: 8(495)118-36-14.

Painting over plaster

What if these items are not plastic? What and how to paint the slopes on the windows?

The quality of coloring depends on the preparation for it. It is important to clean the work surface, prime it with two layers, allowing each layer to dry completely, about 10 hours.

Preparatory work

The stripping process begins with cutting off the protruding parts of the polyurethane foam. All uneven places are immediately leveled by spot applying putty.

After drying, sand with sandpaper to make the surface smooth.

A strip of masking tape is attached to places where paint should not be exposed and to the window frame. Apply primer, leave to dry, repeat.

Non-standard colors for sandwich panels

In addition, any non-standard colors from the RAL catalog for powder coating. The cost will increase by 60 rubles/m² for each side of a non-standard color.

Powder painting allows us to produce sandwich panels of absolutely any color according to the RAL catalogue.

If +60 rubles per sq.m. It’s not critical for you - use any shade according to the RAL palette.

average production time for panels for painting is

Sandwich panels imitating wood, brick or stone are very popular. When viewed from a distance, it creates the illusion of natural analogs that cost much more.

What kind of paint can I use?

Not every paint adheres to plastic panels. Therefore, there are special types of compositions for such material. Today you can easily purchase paint of the desired shade. When choosing paint for plastic, you need to take into account the conditions under which painting will be carried out. It’s one thing when it comes to interior painting work, and another if it’s carried out outside.

If you choose decorative materials, you should know that they are used for decorative designs, and there are special stencils for their application. Technological compositions are designed to reliably protect the surface from damage and wear.

To avoid problems when working with paints, you need to strictly select those materials that are intended for PVC panels. Painting allows you to extend the life of the plastic and make it a decoration for your interior design.

Plastic is often painted with polyurethane water-based paint, the durability of which has been tested in practice. In order for the paint layer to be more durable and last longer, varnish is applied on top of the dried composition. Drying can be done naturally or forcefully.

Today, polyurethane-acrylic water dispersions are also used for painting plastic surfaces. These painting materials are used to paint windows, doors, panels, and other PVC products. The following advantages of using such dyes can be listed:

• These are environmentally friendly paints and varnishes that do not contain solvents;
• The coating applied with such paint serves as an excellent decorative decoration;
• the coating is resistant to deformation and contamination;
• Such paints are water-repellent.

Single-sided sandwich panels

In order to reduce the cost, you can make sandwich panels painted on one side.

On the other side there will be a regular galvanized sheet without a polymer coating.

It will be a little cheaper.

These types of panels are used in hidden thermal circuits, where no one ever looks at them. For example, the roof of an attic floor.

How can you paint a PVC boat?

Self-adhesive film As I have written more than once in my articles, self-adhesive film is ideal for boats in 99% of cases

, kayaks, jet skis and other water-motor equipment with a rigid side. Whether it's aluminum, steel or plastic.

Interesting materials:

Where is the Telegram cloud? Where is the poll on Instagram? Where is the content of the active cell displayed? Where are the reviews on Ali? Where to translate text from English into Russian? Where is the playlist in telegram? Where are the plus and minus on the welding machine? Where did horses originate? Where to receive ePacket parcels? Where to plant Derain on the site?

Recommendations for choosing colors

In general, the color of the “sandwich” can be any.

It is limited only by your wishes.

For the interior decoration of buildings, white panels are most often used; for the façade and roof, multi-color solutions are more suitable, where bright and rich shades predominate.

often also limited by the cultural code of the district or region where you are located.

Sometimes you want to make everything beautiful, but, according to local government regulations, you can only use, for example, gray RAL 7004.

To avoid being forced to repaint, it is better to clarify the possible colors

About Laminate slopes

Laminate is a floor covering, often used for entrance door slopes; it does not require additional processing, it resists mechanical stress. Do-it-yourself finishing has a lot of nuances.

There are two ways to install laminate slopes:

Frame installation. With this technology, you can insulate the opening: fill it with mineral wool or polyurethane foam. The disadvantage of the design is that the slats are placed only in a horizontal position.

Glue installation. It requires a flat surface of the opening, or it must correspond to the dimensions of the laminate. The laminate is glued to the foam (at low pressure).

The first method is preferable for apartments, the second is universal.

Choosing the color of sandwich panels for organization

When choosing the color of panels for an industrial building, it is recommended to give preference to branded shades.

If the building belongs to a government agency, you can choose the colors of the state flag.

If the organization does not have a corporate color, you can choose standard shades offered by the manufacturing company.

Required set of tools

Before you begin processing slopes, make sure you have the necessary tools.

These tools are required for painting slopes

In our work we will need:

• large and small brushes;
• paint container;
• cruvette and roller;
• masking tape;
• ladder;
• construction knife;
• primer and a clean rag;
• fine abrasive mesh;
• liquid acrylic;
• construction pistol.

Expanded polystyrene, rub. per m².

The insulation density is 25 kg/m³ with metal cladding with a thickness of 0.5 .

Please note that sandwich panels with a thickness of 50 and 60 mm do not differ in price.

SovetRemont.com

Dear visitor to my blog! I think you yourself know how important the appearance of window openings is, why painting the slopes on the windows Therefore, I will not engage in demagoguery on the importance of this work and will immediately get to the point.

Preparing to paint slopes

To begin with, the slopes should have a white, clean, dust-free appearance.
You need to achieve this using finishing putty and sanding it with abrasive sandpaper. Perforated aluminum corners should be installed on the outer corners of the slopes; read how to do this here. After cleaning the putty, the slopes should be treated with a deep penetration primer. Attention: if during the process the primer gets on the plastic window frame or glass, then immediately remove it with a damp rag. The window sill should also be protected from contact with primer (for example, polyethylene secured with masking tape).

As soon as the primer has completely dried, we proceed to the next stage - we cover the window frame with masking tape. It is important to do this work carefully and correctly. Use wide masking tape. It should be glued along the entire perimeter, including the junction of the slope and the window sill. The strip of tape should run smoothly without bends, and be pressed as tightly as possible against the supporting frame of the window. Glue the tape along the entire length of the junction of the slopes to the frame with your hands, and then press it as hard as possible with a plastic spatula, this is necessary so that during the main work the paint does not flow under it, this is especially important in the corners of the window opening.

Painting slopes

As for the quality of the paint, it's up to you to choose. Everyone has different financial capabilities, but I still recommend not to buy cheap paint. When choosing, rely on the following three criteria:

1. Over time, as it becomes dirty, the paint should be easily washed off with a foam sponge.
2. Use acrylic, its service life is longer than that of a regular water-based one. When purchasing paint, pay attention to the manufacturer's instructions on the can. Some types of paints have a purely individual composition.
3. If you order online, it will be much cheaper, and if you buy it using cashback, it will be 2 times cheaper! The same goes for buying household appliances or new furniture!

Open the can of paint and mix it thoroughly. Pour a small amount of paint into the tray. Painting should begin from the top slope, moving to the sides. In hard-to-reach junction areas we use a flute brush.

List of tools needed for painting:

• Paint roller
• Flute brush
• Paint tray
• Pliers or screwdriver (for opening paint cans)

Try to roll out the paint evenly with a roller without putting too much pressure on the tool, otherwise greasy streaks and streaks will appear. Before applying paint to the slope, first roll it out with a roller in a paint bath. Attention: the work is done in one go; under no circumstances should you take a break, leaving one side of the window slopes partially painted. If you do this, the paint will dry out and, continuing to work, you will put an extra layer on top of the already painted one. Thus, in this place, at a certain angle and lighting, a non-uniform spot will stand out. If you don’t want to paint the slopes in two approaches, then apply the paint as thick as possible. But again, I remind you, make sure to apply the paint evenly with a roller.

Tips for painting slopes from personal experience

Once you've painted, peel off the masking tape immediately! Do this carefully without haste, being careful not to touch the fresh paint with your hands. Why do you need to remove the tape right away? I answer: the fact is that as soon as the paint dries, it forms a single film, including the paint that got on the masking tape. And when you remove the tape from the window frame, you will pull the dried paint behind it. This results in an uneven painting border; the appearance of such work, to put it mildly, is not very good! If, for some reason, you did not remove the tape from the window frame and the paint has dried, then do the following; Using a standard paint knife with replaceable blades, cut the paint along the entire paint border. After this, you can safely tear off the tape.

Do not under any circumstances try to dry paint with any electrical appliances (heater, hair dryer). The paint must dry naturally, otherwise it will become covered with small cracks, or even completely move away from the base in large “scales”.

If the slopes are not cleaned very well and have large scratches, then use a roller with large pile. Such a roller will easily hide all the flaws of both the putty and its stripping.

Mineral wool [MV], rub. per m².

The insulation density is 110 kg/m³ with metal cladding 0.5 .

Minimum order volume 30 m2 for each item + 20% extra charge Volume from 30 to 100 m2 extra charge 20% production time from 15 working days.

Operational Features

Despite their lightness and rich color range, window panels are classified:

• according to the level of resistance to ultraviolet radiation;
• according to the degree of moisture absorption;
• resistance to abrasive external substances;
• according to the level of resistance to cyclic loads;
• according to the operating temperature range.

Polyisocyanurate foam [PIR], rub. per m².

Installation of sandwich panels from 500 rub. sq.m. To receive a commercial offer, call us at +7(495)118-36-14 or write to us by email

Required set of tools

Before you begin processing slopes, make sure you have the necessary tools.

These tools are required for painting slopes

In our work we will need:

• large and small brushes;
• paint container;
• cruvette and roller;
• masking tape;
• ladder;
• construction knife;
• primer and a clean rag;
• fine abrasive mesh;
• liquid acrylic;
• construction pistol.

Read also

• Materials of sandwich panels - details about the materials of insulation and coating of sandwich panels.
• Fire resistance of sandwich panels - details about the fire resistance of buildings made of sandwich panels.
• Sound insulation of sandwich panels - details about the sound insulation characteristics of sandwich panels.
• Thermal conductivity of sandwich panels - details about the thermal insulation characteristics of sandwich panels.
• Current prices for sandwich panels - + price list in PDF.

Installation of corners and plastic profiles on window slopes

After the PVC windows are installed, you need to install a corner on the window for the slope. This will give the window opening a decorative, finished look. If plaster was chosen as the material for finishing the slope, then the PVC corner will allow you to create clear lines of the window frame.

Item Description

This type of fittings refers to decorative accompanying elements when finishing plastic slopes. As noted earlier, a window corner for a slope can be used to mask corner joints when working with various materials.

The corner is used to mask the junction of the slope and the wall

The decorative plastic corner is made using special technologies, when a rigid PVC sheet is bent using a “hot” method.

The product is universal and is widely used for finishing corners and joints of surfaces made of various finishing materials. Types of plastic corners differ in the material of manufacture and can be made in three versions .

Plastic elements for finishing the slopes of plastic windows have become most popular among consumers. Colored elements can be matched to any interior color scheme. The laminated surface can imitate various materials.